Latest News:

autotechnician - serving the independent workshop - logo

Common Mini EML warning light fault

By autotech-nath on July 1, 2023

Case Study: Opus IVS describe the test process for a common Mini EML warning light fault.

Opus IVS, who provide diagnostics solutions backed by OE master technicians, explain a problem documented for the N12 engine used on 2006 to 2013 second generation Minis

The fault presents with the engine management warning light illuminated and fault code 2968 stored in the Digital Motor Electronics (DME) from the inlet camshaft sensor. This fault can have many possible sensor-related causes – a faulty part, an incorrect part being fitted, faulty wiring, as well as sensor corrosion or damage. It may also indicate a DME internal fault or an inoperative inlet VANOS unit.

The valve gear on the N12 engine is equipped with variable camshaft timing control for the inlet and exhaust camshafts (also known as double VANOS). Both camshaft sensors record camshaft adjustment, via a sensor wheel fixed to the camshaft. The camshaft sensor works according to the Hall effect. Voltage is supplied to the sensor by the DME with 5 Volts and ground. The sensor then returns a digital signal via the signal line back to the DME, see Figure 1.

Figure 1

To begin, start by swapping over the inlet camshaft sensor with the exhaust camshaft sensor – they are the exact same part so this is often a very quick task. The fault migrates to the exhaust camshaft then replace the sensor, see Figure 2.

Figure 2

If the fault stays on the inlet camshaft sensor then proceed to check the wiring. You will need a 5v feed, ground and an intact signal wire between the inlet camshaft sensor and the DME to prove the 5v supply and earth is being provided by the DME, see Figure 3.

Figure 3

Next, check the signal pattern with an oscilloscope. A signal indicates that the sensor is working, whilst scoping at the DME end will also check the integrity of the signal line. The signals, shown in Figure 4, are correct from a verified N12 running engine. Both the intake and exhaust camshaft sensors should have an identical scope pattern, just at different positions on the screen.

Figure 4

The Opus IVS 360 live support team has seen cases where non- OE or used camshafts have been fitted. When doing so, you must make sure the camshaft is an exact match for the part removed. Figure 5 shows the scope trace from an N12 where an incorrect inlet camshaft was fitted. We can see that with this alternative aftermarket part fitted, the inlet camshaft sensor signal has four phases compared to the image on the known good engine with only three.

Figure 5

By scoping the inlet camshaft sensor and exhaust camshaft sensor, along with the crankshaft sensor, the timing of the engine can be checked non-intrusively too using phase rulers and graph rulers as shown, see Figure 6a & 6b below.

Figure 6a
Figure 6b

The Opus IVS DrivePro Elite diagnostic tablet offers a remote services VCI and coverage for 64 brands. It also comes with IVS 360 live support included, from a team of brand-specific OE master technicians. Opus IVS says this example is just one from within a library of hundreds of documented processes which the team can call upon to support customers with live repair guidance.

For even more in-depth solutions, garages can rely upon the pay-as-you-go appointment-based Remote Assist Program (RAP). This brings independent garages enhanced capability to complete a huge range of complex programming and coding jobs on-demand.

www.opusivs.com

SHARE THIS
ARCHIVES

Archives

About Autotechnician
Autotechnician is a magazine published nine times a year, delivering essential information to independent garage owners and technicians in the UK. Delivered both digitally and in print, autotechnician provides readers with technical, training, business advice, product and news, allowing our readers to keep up to date with information they need to run and work within a modern workshop.
©
2024
Aftermarket Media Solutions Ltd, The Joiners Shop, Historic Dockyard Chatham, Kent ME4 4TZ
T: 01634 816 165
Company no. 09625886
linkedin facebook pinterest youtube rss twitter instagram facebook-blank rss-blank linkedin-blank pinterest youtube twitter instagram