Latest News:

autotechnician - serving the independent workshop - logo

The Solenoid Valve Block – a deeper look with Arnott

The valve block is a small but significant component of the air suspension system. Therefore, it should not be neglected when diagnosing possible system defects. Symptoms that seem to point to a leak in an air spring, might also be a defect in the valve block. Let’s start with explaining the general function of the part before diving deeper.

Working principle
The valve block takes care of the distribution of pressurized air. A valve block for a 4-corner air suspension system with pressure reservoir contains a total of 6 air connections: one for the air compressor, four for the air springs/struts and one for the pressure reservoir. To avoid making mistakes when installing a new valve block, all connections are color-coded.


The six solenoid valves inside the valve block are activated by the ECU (Electronic Control Unit). It is a common misconception that the air springs are always directly fed by activation of the air compressor. In most cases the air bellows are filled through the pressure reservoir. The air compressor pressurizes the air in the reservoir up to 15 – 16 bar. This pressurized air in the reservoir is used for controlled pressure build-up and as a buffer. The general objective is to use the pressurized air as efficiently as possible, so the compressor runs as little as possible. This prevents overheating and keeps the energy consumption low.

Defect symptoms and diagnosis
Over time the solenoid valves in the valve block can become sticky or blocked by small particles that have circulated through the system when operating. For example, when an aging compressor breaks down, the valve block can consequentially become damaged too. Due to overheating, small metal particles can block the solenoid valves and disturb the air distribution. Symptom: the vehicle is lower in one or more corners. This symptom could also occur when there is a leak in the air spring.
Fortunately, the actual cause can be easily identified by swapping the concerned air line in the valve block. If the valve block is the issue, the problem should then move to another corner. If the problem stays on the same side, it is indeed an air leak.

The valve block is also involved in the release of excessive air pressure. If needed, the solenoid valve towards the air compressor is opened. The pressure is then released through the pressure release valve on the compressor. Thus, in case a vehicle stays “locked” on a certain ride height, first check the functioning of the pressure release valve on the compressor before diagnosing a faulty valve block.

If an air compressor is no longer running, the usual suspect is often the compressor itself or a faulty relay. But it might just be the valve block. The air suspension pressure sensor is located inside the valve block, not in the compressor. If this sensor isn’t working correctly anymore, the signal for activating the compressor stays out and pressure is no longer built up.

If the dryer no longer has the capacity to keep moisture out of the system, the valve block can corrode internally. Additionally, when the outside temperature drops below zero degrees Celsius, the moisture inside the valve block can freeze causing it to stop functioning.

One last thing to keep in mind is that normally the airline from the air compressor to the valve block is unpressurised if the compressor is not running. This is done to allow the compressor to start easily. If for one of the abovementioned reasons this airline stays pressurized, much more heat is built up each time the compressor is activated. This could lead to a burned-out compressor. So, even though it is small, this significant component of the air suspension system deserves some attention – especially after a compressor replacement.

This information is provided to you by Arnott – Air Suspension Products. With more than 30 years of experience in engineering, designing, and manufacturing high quality air suspension components for the aftermarket, Arnott is the technical expert when it comes to air suspension systems. Arnott’s products are produced with high-quality, OE components offering exact form, fit and function. Each product is extensively tested in our American and European facilities and custom-tuned to suit the specific vehicle make and model before being produced.

About Autotechnician
Autotechnician is a magazine published nine times a year, delivering essential information to independent garage owners and technicians in the UK. Delivered both digitally and in print, autotechnician provides readers with technical, training, business advice, product and news, allowing our readers to keep up to date with information they need to run and work within a modern workshop.
Aftermarket Media Solutions Ltd, The Joiners Shop, Historic Dockyard Chatham, Kent ME4 4TZ
T: 01634 816 165
Company no. 09625886
linkedin facebook pinterest youtube rss twitter instagram facebook-blank rss-blank linkedin-blank pinterest youtube twitter instagram